close
close

How To Cut Vinyl Siding For Ledger Board

Put on your safety goggles, then line up the place you want to cut on your siding with your blade. Use the edge of your table as a guide and slowly saw off the excess siding.


Pin on Got Wood?

I've used it for cutting for a ledger (make sure you get some appropriate j to dress up the cut, just bond it on with caulk) and to terminate porch railing into the siding.

How to cut vinyl siding for ledger board. Sep 7, 2009 #2 cut the siding out and attach directly to structure. What is the preferred method when attaching to a house with vinyl siding. Install the ledger overtop of the siding or remove the siding, attach the ledger and recase around it?

Then slip flashing behind the siding, covering the top edge of the ledger. Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. Removed the siding and i have the ledger resting on what i believe is the vinyl starter strip.

Add 1 ½ inches to each side of the deck width so that hangers can be connected for the joists. The door area is built out about 2 1/2′ , angled at 45 degrees on each side. Make sure you have enough room to install flashing above the ledger board and allow for at least a ¾” space above the decking, preventing water from wicking upwards into wood siding.

Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Push the saw along the line at a steady rate to get a clean, smooth cut. Cut along the line you drew using the circular saw.

Set the blade depth so you won't cut into the house sheathing below the siding. You should position the siding so that the cutting line is hanging off the edge for obvious reasons. When the back flashing needs to be cut around an obstacle, measure for the notch and cut with tin snips, or slice several passes with a knife.

Slip flashing under the siding. For the most secure attachment, ensure the ledger board fastens to the rim joist, just below the floor of the house. How do you cut vinyl siding on a ledger board?

After cutting the siding with a circular saw, install the flashing. Slide the flashing underneath the siding 1 inch. Put the ledger board below the door threshold allowing room for the thickness of the deck materials to be installed.

Use your free hand to hold the vinyl siding down so it doesn't shift while you're cutting it. Then slip flashing behind the siding, covering the top edge of the ledger. Pics of ledger board and vinyl.

Use a nail as a temporary place holder to check. (at least i think this is right.) but because of the vinyl siding i want to make sure i do it right. Slip flashing under siding snap a chalk line, cut out the siding and tack up the ledger board.

Cut away the marked area of siding with tin snips. Step 1 mark the location of the ledger against the siding.the vinyl siding interlocks with itself to form a cohesive. Set the blade depth so you won’t cut into the house sheathing below the siding.

Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Start by making an outline on the siding where you want to position the ledger board. Once again, this contributes to giving the vinyl siding a clean cut.

Slide the flashing underneath the siding 1.slip flashing under the siding.snap a chalk line, cut out the siding and tack up the ledger board. This means that the points of the teeth should be oriented opposite of the spinning direction. Make the outline large enough to include space for the deck boards on top, the ledger and.

The bottom part of the ledger is resting on the vinyl siding starter strip. Snap a chalk line, cut out the siding and tack up the ledger board. My dad is coming up from california he is a construction foreman down there, but does not do any work with vinyl siding so the challenge for me is how to water proof it afterwords.

Start by making an outline on the siding where you want to position the ledger board. Lay the vinyl siding on a flat table or workbench. Overlap flashing by 3 inches and cut it for the doorway.

First, ensure your circular saw is equal to the thickness of the deck, then cut the ledger outline. Lol does the vinyl starter strip need to be removed? I know the standard ledger attachment is to cut out the siding where the ledger goes, install the ledger and proper flashing on top, and caulk the ends of the ledger.

Locate the rim joist and mark an outline on the siding where you want to position the ledger board using a tape measure, pencil and chalk line. I have vinyl siding on the house now and i know i need to cut it away to install the ledger for everything run off of. Watch the blade carefully as you’re cutting to make sure it’s staying on the line.

You may want to place it lower if you intend to step down onto the deck from the doorway. Wood or concrete siding will have to be cut away using a circular saw. Start by making an outline on the siding where you want to position the ledger board.

Use a level to mark the placement of the. When slipping the flashing under the siding, be sure to slide the flashing to the left or right of the ledger by at least 2″.


Pin on Decks


Pin on BWoodworking Tips and Jigs


Learn how to properly install a waterproof deck ledger


How to Create BoardandBatten Siding Looks With


Pin on Decks


Decorative Vinyl Siding Options Cedar Shakes & Board ‘n


Pin on Outdoor ideas


Vinyl Siding Vinyl siding, Vinyl siding installation


HardiePanel siding with PVC trim boards creates an

Leave a Reply

Your email address will not be published. Required fields are marked *